Full enterprise lab walkthrough
A capstone topology with two sites, VLANs, OSPF, DHCP, NAT, and SSH. The walkthrough explains the build order, the verification commands at each stage, and the most likely places to get stuck.
What you'll learn
- Build a multi-site topology end to end without referring to the cheat sheet.
- Verify reachability layer by layer.
- Save and load the topology as a NetForge-AI JSON file.
Topology
Site A — two access switches, SW-A1 for VLAN 10 (Users) and SW-A2 for VLAN 20 (Servers), trunked to SW-Core, a layer 3 switch that routes between the two VLANs. The edge router Edge-A plugs into VLAN 10 and is the site's only link to the internet provider.
Site B — a single switch, SW-B, carrying VLAN 30 (Branch), behind the edge router Edge-B. A serial /30 across the WAN joins Edge-A and Edge-B.
Both edge routers run OSPF area 0 across the WAN and serve DHCP to their own LAN. Edge-A translates both sites' internet traffic to its one public address (PAT); Site B has no provider link of its own. A router named ISP stands in for the provider, with 8.8.8.8 on a loopback as a host on the internet. These are the names the guided build behind 'Open this lab' uses.
Build order — bottom up
- Cable everything; do not configure yet.
- Hostnames + enable secret on each device.
- Switches — VLANs, access ports, trunks between SW-Core and the two access switches.
- L3 switch — ip routing, SVIs, default route to Edge-A.
- Edge routers — interface IPs, OSPF, a static route to VLAN 20, the default route to the ISP, and on Edge-A only, ip nat inside/outside and PAT.
- DHCP pools on each edge router for its local LAN.
- SSH on every router/switch (hostname, domain, RSA key, transport input ssh).
- Verify with: show ip route, show ip ospf neighbor, show ip dhcp binding, show ip nat translations, ping end-to-end.
- Save the finished topology as a JSON file you can load again.
13 more sections in this chapter, plus a 4-question quiz and a hands-on lab.
Modules 2–8 are part of the Course & Lab Pass and All-Access Max — start with a free account
You can see the title, summary, learning objectives and the opening sections. The rest of this chapter, like all of modules 2–8, comes with the Course & Lab Pass and All-Access Max. A free account opens Module 1: How Networks Work end-to-end and saves your labs — start there, no card required.
- Read every chapter in Module 1 — How Networks Work
- Save labs of up to 5 devices
- Save up to 3 topologies
- See the full course syllabus + chapter titles
Free account · no card required · compare plans any time
Build it step by step
- Share one default route with OSPFGive the edge router a default route to the provider, then let OSPF hand it to the rest of the campus instead of typing it on every router. · 7 steps · ~22 min · 5 devices
- Fix it: Fix the branch that fails four waysA branch depot has lost head office, and two of its hosts have faults of their own. Find all four, one layer at a time. · 10 steps · ~30 min · 7 devices
- Campus capstonePut it all together: two wiring closets, two VLANs, DHCP for the desks, and one public address for the whole site. · 9 steps · ~35 min · 8 devices
- Redundant campusDouble every link and box between a desk and HQ — bundled, spanning-tree protected, VRRP gateways, twin OSPF circuits — then break two of them and keep working. · 10 steps · ~50 min · 8 devices
- Enterprise capstoneThe Module 8 capstone: build a two-site enterprise from bare devices — VLANs, an L3 switch, OSPF over the WAN, PAT to the provider, DHCP per site and SSH — verifying every layer before the next. · 23 steps · ~75 min · 10 devices